Відео

Does stainless steel also break easily

Thanks for the video, it is very helpful, I found that the carbon brushes in my motor are completely damaged. I have a question, do you know if the carbon brushes can be replaced?

Do not throw your money away changing the sockets. This will only make 2 results: 1. this will improve starting off (launching) 2. this will increase your RPM in top gear at highway speeds. Changing the sprockets is changing the final gearing on your cycle. Changing the final gearing means nothing. What really matters is overall gearing. Overall gearing is everything from the engine to the rear tire. Overall gearing is a affected by these areas: 1. Manual Transmission 2. Drive sprockets (final gearing) 3. Tire size (actually have to change rim diameter to change tire size much) It is a very common misunderstanding that changing the sprockets will mean you'll always have lower gearing. That is not true. You have a manual transmission. That allows you to have what ever gear ratio you want. If you like the power of low gearing then don't shift until redline for all I care. Shifting at redline is not what you really want unless you are drag racing. My point is you can decide how high you want your RPM to go before shifting. If you like low RPM for fuel efficiency shift early and keep your RPMs low. Once you get in top gear you can't shift up any more. That's why I say changing the sprockets will affect the RPM on the highway.

Helo, thanks for your video, very instructive. I have a four pasenger car which uses a three 120° marks bolts in the head is a korean car. What should it be the working tork it should hold? Do you know what the Korean automotive manufacturing car code is? Thnaks a lot in advance.

my pedestal fan has a new capacitor and the motor is ok but the fan is not running what is the main problem?

check oil after loud noises and vibration...

Thank you for posting!😊

Electricity flow from negative to positive the electrons are actually flowing from the bottom of the battery into the contact go all the way around to the light bulb and back into the top of the battery😊

Very good video, gave me the knowledge and confidence to unplug the wires from the switch, test it, and open it up. But turned out it was all good and the problem was a blown thermal fuse which explained the "no power / no lights". Managed to fix that and the unit is back in service.

HAHHAHAHAAHHAAHAHAH worse video ever for showing a bike at idle and measuring the temps.

Priority bike with belt drive no chain👍

i worked in the biggest engine remanufacturing plant in north america. we used to buy cranks like this for 75$ spend 5$ changing the bearing and reselling them for 500$. if you have a press and a good micrometer you can do it yourself if you have a bit of time. the hardest is to make the crank wooble free after reassembling it. you need to buy a needle micrometer and a good non-marring hammer and wack it.

I was having trouble replacing the battery on my Casio STR-300 because the instructions were in Japanese. I'm glad I stumbled onto your video. Your explanation on how to do the AC reset saved me a trip to a watch repair shop. 🙏Thank you very much!

This is my second TOASTMASTER... BRAND NEW! Doesn't work. POS ... A $20 Piece Of Sh**

Ya right tear up the screws and end up loosening the rails.

You’re the man, just wanted to know what size socket I needed to grab my work box tmr

Thank you for the post, had difficulty finding the spring loaded clasp as it was very tight, also was surprised to find the halogen bulb behind the fixture

Thank you for saving my life.

Great. I have the same model, strap fell apart, so once I source the replacement I will follow the instructions. Thanks

Bro speaking from experience good video tho

Thank you so much great job God bless you for helping me fix my tablet I highly recommend this channel thank you Jesus

I never know when to test for continuity and when to test for resistance🤨

Thanks for that. A suggestion, you should get that blood blister checked out. I’m serious Cheers DJ

You should have waited 4-5 hours before driving your bike.

Ten years later and I appreciate the video, thx man you helped me a lot with my build. Cheers!!

😢

Thanks mate, you saved me

I came for how to put the back of the seat down. THe bottom just pops out. That was beyond easy. I still can't get the stupid back down!

Just about to trash my blender and then I saw this video...wow great video!!! Save me $75. Thank you!!!

Very well done. Covered pretty much everything. Unfortunately my switch is completely sealed . I ordered a new one with a higher amp rating than mine but I believe all the mounting locations are same. I'll know when Amazon drops it off in a day.

He deserve a subscribe

5:46 I won't get back. So, did you simply pull up on that seat to remove it ??? This was titled as a rear seat REMOVAL video. You did the reinstall !

Thanks I did it because of your knowledge share

Please I have the same fan It is working but can stop on it own, what may be the problem Sometimes work correctly sometimes on and off

thanks fella

Great video, subbed.

Don't you love it when they manufacture it so the whole part has to be replaced and not just a bush? Planned obsolescence 101. My wing mirror had a scratch on the plastic cover, which comes off easily, but they wanted to sell me the whole mirror. I ended up just vinyl wrapping it and told them to go F themselves.

My bike was warm and i closed the choke but my stayed high up 300rpm.How can i fix this problem..i keep messing with the idle screw to bring it back down to 1500rpm

Nice video

Thanks. This will solve my problem.

This is very helpful video. Thank you,

river looks bad... id change it..with proper tool.. not just hamer ...also this rivet is not for hamering..just ping goes up..river is pin have a hole.. to push on outside...

Broken clip now why???

Thank you, thank you!!!!! Much appreciated for you creating and posting this video!!! I was about to hire an electrician to come replace my light bulbs after an hour of frustration!!

Hi, is it possible to make a video on how to change 1 of the clips, since 1 of them broke from mine?

In the video he is screwing the brake light switch. This will twist wires coming out from the brake light switch and possibly damage them. What you should do is hold the brake switch tightly and rotate the hex screw instead.

Lmao wth

and thats what nutral is for

Too much bla bla bla

THANK YOUUUUUU! You lifesaver